TERAHERTZ PROBING – From sub-nanometers to micrometers

Contactless Terahertz microprobes can measure the sheet resistivity and thickness of large-area conductor films at unprecedented speed and resolution.

Emerging terahertz technology is on course to define the next state-of-the-art for thin-film conductor inspection [1]. A recent example is given by a novel instrument employing miniaturized terahertz near-field detectors [2]. Non-destructive high-resolution inspection of various conduction layers as used in touch-screens, electronic paper, displays, solar cells or OLED devices is efficiently accomplished by this new technology.


While THz radiation can virtually not be transmitted through highly conducting bulk materials it penetrates fairly well through thin conductor layers with a thickness below skin-depth [3]. This property can be used to measure the absolute sheet-resistance and (indirectly) also the thickness of many technically relevant conductor layers under the usually satisfied assumption of constant bulk conductivity. THz radiation is sharing this property with microwave or even longer wavelength radiation. However, high-resolution measurements are much more difficult in these low-frequency regimes and thus have only been available for small measurement areas on the order of 100 µm x 100 µm using atomic-force-microscope-type equipment. Other methods which can be used for full-wafer mapping (like Eddy-current measurements) suffer from very low mm-scale spatial resolution. The THz microprobe-based technology is now enabling micron-scale resolution and high-speed full wafer mapping which has not been possible up to now. This increased performance is supplemented by capabilities to measure layers buried under isolating capping layers and generally contact-free probing.

Measurement results

In Fig. 1 the dependency of THz transmission against layer thickness is shown for some selected conductor materials. The accessible thickness range extends from sub-nanometers for a single layer of graphene to the micrometer range for indium-tin-oxide (ITO). The corresponding sheet resistance range is from sub-Ohm to some k-Ohm per square. For optical measurement systems such a large range of thickness values is usually inaccessible. In case of ellipsometric measurements a pre-knowledge of the approximate thickness value may allow the execution of measurements, but only in a small few-nm-range of thickness deviation.
Fig. 1

Fig. 1: THz transmission amplitude versus layer thickness of selected conductor layers.

In Fig. 2 an exemplary sheet resistance plot measured with a THz microprobe is shown. The investigated sample is a glass wafer covered with TiN and Ti layers of various thicknesses. The measurement speed is up to 5 ms/data-point which is sufficiently high to enable high-resolution full wafer mappings in a few minutes and up to three orders of magnitude higher compared to standard methods like four-point-probing or spectroscopic ellipsometry. The observed sheet resistance values range from 6 Ohm to 400 Ohm per square corresponding to 7 nm – 230 nm of TiN. The well visible radial increase of sheet resistance refers to a thickness decrease of up to 20% caused by a sputtering process inhomogeneity.
Fig. 2

Fig. 2: (Right) wafer-scale mapping of sheet resistance values measured at a glass wafer covered with differently thick TiN and Ti layers. The black area refers to uncovered glass. (Left) Colour-scale plot high-lighting the sheet resistance inhomogeneity within the marked wafer area.

[1] M. Nagel, A. Safiei, S. Sawallich, C. Matheisen, T.-M. Pletzer, A.A. Mewe, N.J.C.M. van der Borg, I. Cesar, H. Kurz, “THz Microprobe System for Contact-Free High-Resolution Sheet-Resistance Imaging,” 28th EU PVSEC conference, 30 September 2013 – 4 October 2013, Paris.

[2] http://www.amo.de/?id=798

[3] M. Walther, D. G. Cooke, C. Sherstan, M. Hajar, M. R. Freeman, and F. A. Hegmann, “Terahertz conductivity of thin gold films at the metal-insulator percolation transition,” Phys. Rev. B 76, 125408 (2007).


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )


Connecting to %s